Some people have good care for the car, and they can't see that their car is a little dirty, and some people are "pragmatic". I think the motorcycle is used for it, so why bother it. In fact, for the basic cleaning and maintenance of the baby, I think it is necessary.
Today, we will popularize some chain cleaning and maintenance knowledge from the cleaning and maintenance of the chain!
Second, the harmful effects of depositing sludge on the chain
1. Accelerate chain wear
The formation of sludge - the motorcycle rides over a period of time. As the weather and road conditions are different, the lubricating oil on the chain will gradually adhere to some dust and fine sand. A layer of black thick sludge is gradually formed and attached to the chain, and the sludge will also cause the original lubricating oil of the chain to lose its lubricating effect. The fine sand and dust in the sludge will continue to wear in the transmission process before and after the toothed disc, the teeth of the toothed disc are gradually sharpened, and the clearance gap with the chain is getting larger and larger, and abnormal noise may occur.
2, accelerate the chain lengthening
The sludge will not only wear the sprocket wheel, but also wear the connecting shaft between the chains, so that the chain is gradually elongated. At this time, the tension of the chain must be adjusted to avoid abnormal noise, unchaining and power failure.
3, not beautiful
The deposition of a layer of sludge will make the chain look black and black, and even make people look disgusting. Even if the motorcycle is washed clean, the chain is always cleaned with water.
Third, the chain cleaning and maintenance process
1. Preparation materials: chain set (cleaning agent, chain oil and special brush) and fee board, it is best to prepare a pair of gloves. Vehicles with large frames are more convenient, if you can't consider using the frame.
2, clean the chain steps
A. First, you can use a brush to remove the sludge from the chain, so that the thicker sludge is loosened and the cleaning effect is improved.
B. In the case of a large frame or a frame, the rear wheel of the vehicle can be erected and hanged. Use a cleaning agent and a brush to make a preliminary cleaning step by step.
C. After removing most of the sludge, the chain reveals the original metal, and then sprays it with a cleaning agent to completely remove the remaining sludge, and the chain is also a natural color.
D. In the case of site conditions, after cleaning the chain, rinse the chain with water to make some sludge stains that have not been completely washed down, and then wipe them clean with a dry cloth. If there is no site, after cleaning the chain, wipe it off with a dry cloth.
E. After cleaning the chain, it can restore the original metallic color. In this case, the ball chain oil and then the alignment chain, a circle can be sprayed, remember not oversprayed, as long as a small amount of ejection circle, still 30 minutes, the oil slinger is not easy.
F. On-site cleaning - because the cleaning agent is easy to sputter to the hub. So in the end, wipe the wheel with a damp cloth dampened with detergent, wrap the stained cardboard and discard the ground.
Fourth, the benefits of using chain oil
The use of chain oil, the better side is to make a certain formula upgrade of the chain, adding anti-wear molybdenum disulfide, and the use of better oil base, so that the chain oil is not easy to oil like oil, chain oil They are all bottle-type spray cans, which are more convenient to use and carry.
Five, chain cleaning and maintenance cycle
Chain cleaning cycle: It is recommended to clean once in 2000-3000 km, or feel that the chain is dirty and can not be cleaned.
Upper chain oil cycle: 200-300 km is recommended, spray once, spray one turn, not more spray. Or medium and long distance, spray once a night before departure. If it is a long trip, it is recommended to bring the chain oil directly. Special reminder to the riders, after riding in the rain, it is best to last chain oil. Because of the scouring action of rain, the chain is easy to interfere.
The final product will be 40%-45% tire oil (fuel oil), carbon black and 35% carbon black, 10% steel and another 5-10% recycled gas (CH4-C4H10).
The main process is to pyrolyze the tire into oil and gas by directly heating the reactor;
The condenser or cooling tube will cool the gas to a liquid oil with the aid of circulating water;
Then, the remaining gas that cannot be cooled into liquid oil is recycled to the reactor heating system; after the oil and gas is completely discharged, the reactor is stopped to be cooled, and the reactor below 70 degrees is cooled; then the door can be automatically opened and the carbon black can be discharged. .
The capacity of each batch of products ranges from 5 tons to 20 tons.
LN-2200-6000 capacity 5-6 tons
LN-2200-6600 has a capacity of 7-8 tons
LN-2200-8000 has a capacity of 9-10ton
LN-2600-6600 has a capacity of 10-12ton
LN-2600-8000 has a capacity of 12-14ton
LN-2800-6000 capacity is 10-12ton
LN-2800-6600 has a capacity of 12-14 tons
LN-2800-8000 capacity is 15-20ton
If cut into small pieces, it can handle more.
Free Installation Tires Pyrolysis Equipment,Waste Tires Pyrolysis to Oil Equipment,Free Installation Pyrolysis to Oil Equipment,Latest Waste Tyre Pyrolysis Machine
Henan Lanning Technology Co., Ltd , https://www.lanningrecycling.com