Zn/Zinc Adhesive Wheel Balance Weights Z110

Find HOPSON TYRE REPAIR® @ Essen 2016 in Germany during May.24-27, 2016.

Booth Number.: 11H26

 

We are now looking for worldwide agents for HOPSON TYRE REPAIR. If you are interested, please contact us today.

 

General Info:

 

Part No.: Z110

Height:4.0mm(include tape 5.0mm)

Width:18mm

Length:130mm

Packing: 100strips/box, 4boxes/ctn, customized is also welcomed

 

Description:

 

HOPSON POWER WEIGHT offers a complete range of quality coated, non-coated and adhesive Wheel Weights for passenger cars, motorcycles and trucks. HOPSON Coated Wheel Weights are polyester coated(silver-grey) to prevent material staining on the alloy wheel. HOPSON adhesive wheel weights are pre-cut and require no additional cutting. A simplified organizational system makes wheel weight selection and application easy. Our goal is to become a partner, not just a product supplier. HOPSON POWER WEIGHT guarantee that its products will meet and exceed the highest quality standards in the industry. We are committed to ensuring your success.

 

The 60grams zinc adhesive strip, made up of 6x10 grams segments.

 

OEM is welcomed.

 

Installation of Adhesive Weights:

 

Pre-treating the rim:

Clean the rim thoroughly with a cleaning agent that is compatible with varnish(e.g. IPA 70%) in order to remove any residual grease, silicone or adhesive.

Please note: A minimum of 15ºC is required in terms of both the room temperature and the rim temperature.

 

Pre-bending the weights:

Separate the correct gram(as calculated) from the bar. Mould the shape of the weight to match the rim radius(with protective film).

Please note: You need to bend the weights gradually, otherwise they will break apart at the joins. You should bend the weight to a little more than the rim's radius.

 

Removal of the protective film:

Remove the protective film.

Please note: Do not touch the glued surface after peeling off the rim.

 

Sticking the weight on:

Attached the weight to the calculated point on the rim, making sure that the weight is distributed evenly either side and the weight is parallel with the edge of the rim.

Please note: Press down on the weight hard, working from the centre to the left and right. A minimum pressure of 1kg/cm2 is required. The angle of the sticking surface should not be higher than 15 ºC to normal.

 

 

Find HOPSON TYRE REPAIR® @ Essen 2016 in Germany during May.24-27, 2016.

Booth Number.: 11H26

 

We are now looking for worldwide agents for HOPSON TYRE REPAIR. If you are interested, please contact us today.

 

General Info:

 

Part No.: Z110

Height:4.0mm(include tape 5.0mm)

Width:18mm

Length:130mm

Packing: 100strips/box, 4boxes/ctn, customized is also welcomed

 

Description:

 

HOPSON POWER WEIGHT offers a complete range of quality coated, non-coated and adhesive Wheel Weights for passenger cars, motorcycles and trucks. HOPSON Coated Wheel Weights are polyester coated(silver-grey) to prevent material staining on the alloy wheel. HOPSON adhesive wheel weights are pre-cut and require no additional cutting. A simplified organizational system makes wheel weight selection and application easy. Our goal is to become a partner, not just a product supplier. HOPSON POWER WEIGHT guarantee that its products will meet and exceed the highest quality standards in the industry. We are committed to ensuring your success.

 

The 60grams zinc adhesive strip, made up of 6x10 grams segments.

 

OEM is welcomed.

 

Installation of Adhesive Weights:

 

Pre-treating the rim:

Clean the rim thoroughly with a cleaning agent that is compatible with varnish(e.g. IPA 70%) in order to remove any residual grease, silicone or adhesive.

Please note: A minimum of 15ºC is required in terms of both the room temperature and the rim temperature.

 

Pre-bending the weights:

Separate the correct gram(as calculated) from the bar. Mould the shape of the weight to match the rim radius(with protective film).

Please note: You need to bend the weights gradually, otherwise they will break apart at the joins. You should bend the weight to a little more than the rim's radius.

 

Removal of the protective film:

Remove the protective film.

Please note: Do not touch the glued surface after peeling off the rim.

 

Sticking the weight on:

Attached the weight to the calculated point on the rim, making sure that the weight is distributed evenly either side and the weight is parallel with the edge of the rim.

Please note: Press down on the weight hard, working from the centre to the left and right. A minimum pressure of 1kg/cm2 is required. The angle of the sticking surface should not be higher than 15 ºC to normal.

 

 

Finger Plug-In Cotton Pag Making Machine

This machine adopts ultrasound and cutting to produce plug-in cotton spunlace non woven facial pads automatically. We can do different cotton pad layers and patterns according to customer requirements. The machine can reach the speed of 260-400 pcs/min. We can make the machine according to the customer's detailed requirement. Only need to change the mold of different products size.

Finger Plug-in Cotton Pag Making Machine

Finger Plug-In Cotton Pag Making Machine,Disposable Inserted Cotton Pad Machine,Hand Inserted Cotton Pad Machine,Hand Inserted Cotton Pad Making Machine

KYD Automatic Mask Machine Factory , https://www.kydultrasonic.com