Magnetic float level gauge is a commonly used product type of liquid level gauge, with the advantages of intuitive display, no need of power supply, low maintenance, low maintenance cost, etc. It is an upgraded product of glass level gauge replacement.
Daily failure analysis of magnetic float level gauge:
1. The magnetic float level gauge was calibrated properly. After the floater was used, it was found that the float had a “sucking†phenomenon at a certain position. This is mainly caused by the distance between the liquid level gauge and the steel plate when it is installed through the steel platform. Therefore, installation through the steel platform requires special attention to the spacing between the tube wall of the level gauge and the cut edge of the platform. According to the experience in the field, this distance is about 100mm, which can ensure no impact on the magnetic float.
2. Occasionally, the on-site adjustment will find that the float is not flexible enough to move up and down. This is mostly due to improper installation. At this time, pay attention to whether the center of the upper and lower flanges is on a line and is perpendicular to the horizontal plane. In general, the angle with the horizontal plane is preferably not less than 87 degrees. If the deviation is large, it may affect the smooth movement of the float.
3. If the closed glass tube used for on-site instruction is broken due to transportation or other reasons, the glass tube can be replaced by domestic glass. But it's best to vacuum. Also note whether the glass tube is vertical so as not to affect the indicator's indication.
4. When the magnetic flap level gauge is used for a period of time, it is difficult for the float to float and the float to move is not flexible. This is basically due to the iron float or other dirt on the magnetic float. The medium may be evacuated first, and then the float may be removed to eliminate iron chips or other contaminants on the magnetic float.
5. When the level gauge is put into use on site, special attention should be paid to opening the upper gate valve first and then opening the lower gate valve. This is due to the fact that the bottom of the communicating tube of the magnetic float level gauge is equipped with a thrust spring which protects the float. Otherwise, the effect of large differential pressure may crush the float and render the level gauge unusable.
6. When the level gauge is used, special attention should be paid. Do not use a strong magnet to pull the float on the outside of the connecting pipe to check it. Otherwise, the magnetic float will change its polarity and even weaken the float so that it will be difficult to work normally.
7. During the use of the level gauge, if the output signal produces frequent disturbances or interference pulses, it is necessary to check whether the signal cable shield is grounded reliably. The working connection is whether the resistance can meet the requirements. If the interference is still not completely eliminated, a signal isolator can be used.
8. Use intrinsically safe liquid level timing, especially pay attention to whether the impedance of the level gauge and safety barrier matches. Because this level meter power supply voltage is 14.5-36VDC, which is smaller than the 14.5-45VDC of the general transmitter, it cannot work normally when the load is large.
The above is the daily failure analysis and processing of the magnetic level gauge provided by Xiao Bian for everyone. We can do some reference based on the above content, hoping to help the user to properly learn some of the application knowledge of the magnetic level gauge. Through the above brief introduction, people only use the magnetic level gauge in the process to avoid the above matters, in order to achieve the correct use of magnetic level gauge, to maximize the role of magnetic level gauge.
Flying Laser Marking Machine
The operation of the current type of flight Laser Marking Machine not only brings considerable prospect to industrial efficiency, but also has the function of saving people, time and energy. To engrave mark printing process, industrial products on the assembly line in the present is the production line flow, which in turn in the industrialized production efficiency effectively, thus to increase production efficiency and effective. The pursuit of automation, intelligent laser line processing, the principle of flying laser marking machine, vibration will mirror scanning the movement of the workpiece on the assembly line and combination, constitute the laser marking system is called laser printing system, also known as flying marking system.
1. It is required that the contents of the code should not be too complex, otherwise, the marking speed will be affected;
2. Cooperate with the assembly line directly, reduce loading and unloading manpower, and operators can avoid bad production environment;
3. Automatic production, greatly improving the efficiency;
4. The speed of spraying code is fast and the output is increased.
Flying Laser Marking Machine,Flying Fiber Laser,Co2 Flying Laser Marking Machine,Laser Flying Marking Machines
Zhongcan Technology Co.,Ltd , https://www.zhongcantechcn.com